The MK 4 version continues the GLAND’s heritage, but in a smaller and sleeker overall size which should appease many riders. The images beside show the top, profile, and under side of each guard.
The new Gsport Uniguard is a simple, inexpensive functional guard that eliminates the need to spread the dropouts. It’s made from Heat-Treated Cr-Mo Steel and is LHD and RHD compatible as well as Drive and Non-Drive compatible. All bases covered. Available in 14mm or 3/8?.
- Sold in pairs - Allen wrench included
Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
The M2 lever works with a single cable or Odyssey's dual cable system. - Improved braking power for Gyro users - Left/Right hand compatible
- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)
- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.
The Slim by Four is a BMX-specific brake pad with a symmetrical shape designed for both forwards and backwards braking. A custom inner frame helps to stiffen the pad and prevents excessive braking power from being lost to flex. SPECS - Clear and Gum colored “Soft” compound pads provide extra grip on powder coated rims. - Black “Normal” compound Slim-By-Four pads are the most popular pad choice for most riders.
- New ultra-slim 2014-T6 aluminum seat clamp with replaceable hardware and self-aligning nut. - 6061-T6 aluminum construction. - Standard 1-1/8-inch size.
Broc Raiford can bunnyhop over a house so it’s only right that he has his own grips to hold on to. Broc’s signature grip comes in at 160mm in length and features rope detailing on the ends to tie in with Broc’s nautical theme.
The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing (2.9 oz). - Black - 60 – 65mm
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield lever is easy to install and remove without having to wrestle grips on and off. An ordinary hinged clamp can be bulky and expensive so a new clamping design made specifically for die-casting was used. This approach keeps the lever reliable and affordable. The lever handle is the same comfortable shape as the proven Monolever Medium blade.
This is Odyssey's top-of-the-line brake cable that ties together all of their most advanced braking technology. - Utilizes the original BMX Linear Slic Kable housing to prevent binding when the bars are rotated. - Factory installed ferrule ends with inner volcano shape to prevent housing blow out; a Linear Slic Kable standard since 2008. - Specially coated inner wire for ultra low friction, a proven feature resurrected from their once famous Brakeline cables. - Gyro lug included at one end of the inner wire for use with detanglers. - 60-65mm in length. - Black
$13.99 - $16.99
One of the most successful and popular pedals, and for good reason with its extremely simple, lightweight, inexpensive and famously durable plastic-bodied design. Often duplicated but never replicated. - High-strength plastic composite
For the Bluebird chain, Odyssey took the proven and reliable KMC 510-HX chain and added a permanently attached, factory installed half-link to one end. When the chain is trimmed to size you can easily decide whether or not to use the half-link. Original factory assembled pin joints are radically stronger than workshop assembled ones, so this is a huge benefit.
- 4140 Chromoly - 3 Possible peg positions for longer peg life - 14mm with 3/8-inch adapters included - 4 inches (length) x 1-3/8 inches (outer diameter) - Sold in pairs - 8.75 oz (17.5 oz for a pair)
Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro since 1986 and constantly improving it along the way. Everything you need to run a Gyro. Odyssey Gyro cables and upper and lower cable stops included.
The Monolever was an instant classic and has become a clear favorite with pro riders around the world because of its familiar feel, smooth edges and variety of handle options.
- Straight gauge spokes with a proprietary grade of stainless steel that is as good or better than the materials used by the world’s most renowned spoke makers. - Sized and dimensioned specifically for BMX.
New dust cap design, with Monogram laser etched logo, for a cleaner look to accommodate a taller riding set up with less spacers. Same quality as Odyssey's Pro Headset using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 15mm dust cap. With 3mm, and 2mm spacers - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1 1/8-inch integrated headset. - 45º tapered bearings - 41.8mm outer diameter (fits 42mm BMX head tubes).
Designed specifically for use with Odyssey's Quartet FRONT or REAR hubs. SPECS - Forged from 7075-T6 aluminum for greater strength and durability - Steel insert prevents guard deformation, prolonging bearing life
Mike Aitken's popular signature tires for street and dirt. Ideal for use at high speeds. - 20 × 2.25, and 20 x 2.45 Dual ply casing
Odyssey is proud to offer their new tripod post. It allows for the two most popular seat angles amongst riders and it’s clean, light and easy to install. SPECS - 25.4mm diameter - 6061-T6 Aluminium, CNC machined
This plastic peg features a full 4130 core with a long-lasting, fast-sliding, plastic sleeve. - 1.5-inch outer diameter - 14mm with 3/8-inch adapter - Sold individually - Weight: 7.6oz - Replacement sleeves sold separately
Designed using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 10mm, 3mm and 2mm (15mm total) - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1-1/8 integrated headset. - 45º tapered bearings 41.8mm outer diameter (fits 42mm BMX head tubes).
It’s a traditional straight up pivotal design with a 200mm length.
The Springfield Brake Kit will provide easy braking upgrades along with value, as the kit will be more affordable than buying each part individually. All necessary hardware will be included as well. Doesn't get much better! - One spring design - Comes with GHOST PADS - Hinged lever clamp - Medium sized lever
A huge leap forward in pedal technology that results in a simpler overall design. Extremely lightweight plastic bodies eliminate the need for bearings and allow for a spindle that is significantly stronger than normal. Metal pins make the pedal very grippy, and the pedal will still function normally when pins are removed from one side for grind tricks. No flimsy outboard end caps. Pedal body halves are easy and inexpensive to replace – instead of replacing the whole pedal. - 9/16-inch, heat-treated, 4140 chromoly spindle - Proprietary high-strength plastic composite
Page 1 of 2 Next page